Turnbuttons, turnbuckles, twist snaps what ever you might want to call them, these are what we use every 12". They are attached with 2 stainless steel screws, there are very little problems with these, and are great compared to snaps.

The front is usually designed in 3 pieces so you have zippers at the corners for easy access and big doors, or we can put in a roll up door for you. There are normally 3 exterior stake down straps per piece.  We can also put them on the inside if you like.

In your sewer area there is a zipper for sewer access, with 2 zipper heads so that the opening is adjustable around your sewer line or pipe.  There are also zippers for your valves--we make these openings big enough to get into even if you have on a large jacket. If needed we also make a zipper opening for your water line should it exit below the skirt.  

Slideouts have an extra piece of material on each corner inside just in case it might wear on the skirt or be sharp at the ends. We put snaps only on the ends where it slides in and out (if we put turnbuttons there it would rip them off). When possible we try to make the slideout in one level piece. The corners of the bottom pockets are oval cutouts so it's easy to slide in pipe or PVC.

Jacks that may be close to the skirt or any other sharp objects also get an additional piece of material inside to protect the skirt.

Back bumpers and ladders are cut around frame supports and Velcro holds the parts together giving you a nice line around. If your license plate is in a recessed area we can go up and over to cover it or under, it is your choice.

In the door areas we make a slit for the steps, bring the material up in behind and snap it under your door--we use snaps her so you don't trip on the turnbuttons.

We have a few ways we can cover or go around your cabinets or openings, we can go straight across if you do not need access into them, can make drop down openings with Velcro or zippers so you have a nice straight top line but can access your doors, or we can go down and around if you are into these doors quite a bit and prefer not to bother with the skirt each time.

There is a 5" pocket on the bottom of the skirt for PVC or pipe, along this bottom pocket we back stitch about every 18 inches so if a thread is ever cut on the bottom it could not come loose all the way across, we supply 1-1/4" pvc pipe and cut it into 5' pieces for you, this makes it easy to store in the storage bags we give you. There are 2 large bags for the skirt and 2 long thin ones for the pvc, this way you can store each side in a different place and not have to carry all things in one heavy bag.

Zippers are YKK #10, the heaviest and the best marine quality zippers on the market.  We double stitch them on and stitch over the top part aprox 6 times, if a zipper would come loose it would be from the top, with this much stitching we have not had a zipper come loose for this reason.

The thread normally used is black or white #92 Ultra Bond, UV protected, we can also us colors to match, sometimes colored thread is not as large and may fade out after some years.

If you would like an extra zipper or 2 for one reason or another this is not a problem. There may be a slight extra charge per zipper.

Our skirts are measured at your wheels, we add on aprox 6" extra for uneven RV Parks, if you don't need it, it rolls under out of sight, the stake down straps still work, they are 13" long. We can make the skirt longer if you wish or shorter if you don't plan to move your RV, the choice is yours.

Straps are 13" long, the material is rolled so there is 3 layers of material to nail through, it's strong, we can put these inside or out.  If you do not want to nail your skirt in place or are on cement we can supply sand bags in place of this.

8" galvanized nails hold the skirt in place even in high winds, we leave them up just a bit so if you have to move in the coldest of winters you can still get a good hold on the nail and pull it up.

We also make large hems on the ends for strength, we try to design these skirts to last for years.

Material used is all 18 ounce, we use Vinyl-Tex, 22 ounce is available in black and white only Add $50.we have a few other materials we can use which are a bit more expensive.

The only real add on is an additional piece that separates the front 5th wheel part from the back part, there is an extra charge for this piece. 

Our do it yourself skirting is sold by the foot, can have snaps or turn buttons on it every 12". It is our lowest cost skirting made of 18 Ounce Vinyl Tex. You will need to measure your RV so we know how much skirting you will need and the height of it. We have many diagrams that you can print out to help out depending on your style of RV.

When measuring the height that you want your skirt to be, make sure to add on a few extra inches for uneven RV parks. 

We send most things you will need for your skirting and have a few extras that you can purchase. Included is extra material to go over or in behind the step areas, or for over fenders. All the snaps or turnbuttons and  stainless steel screws needed and some glue to attach fabric together or make repairs.

When you measure the pieces you need we will add one foot extra to the ends for overlapping

Stake down straps are also included, you can glue them on where you need them... its easy!

Colors: Black, White,    22 ounce is Available